Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
PGT Fence Installation: The Dallas Owner’s Guide
PGT fence installation in Dallas typically runs $3,500 to $9,000 for a complete panel and post replacement on an average residential lot. We stock PGT-compatible fence hardware and panels at Bradford Remodeling Co Dallas, and most swaps are done in one to two days once materials are confirmed. Homeowners usually call us after a storm, when a post has rotted at ground level, or when a gate has sagged to the point it won’t latch. In Dallas, the biggest enemy of any fence line is the clay soil and summer heat, which cycles wood and composite materials through extreme expansion and contraction every year.
Which PGT Models This Applies To
PGT doesn’t manufacture a single fence line, so the first step is always identifying what you actually have. The most common PGT fence product we see in Dallas is PGT’s aluminum and vinyl fence systems, typically used around pools, patios, and perimeter enclosures. Check the horizontal rail for an embossed or printed label, usually near a post cap or on the bottom rail. If the label is gone, measure the picket width and the rail-to-rail spacing. PGT aluminum sections are almost always 6-foot wide panels with a 2-inch square post profile. Vinyl is different: PGT vinyl fence runs 1-3/4-inch to 2-inch rails with tongue-and-groove pickets that interlock.
Here’s the compatibility gotcha Dallas owners run into all the time: PGT aluminum fence sections use a proprietary bracket system. Big-box aftermarket brackets will not seat correctly on PGT’s rail design. We stock OEM-spec bracket kits and full sections. For vinyl, quality aftermarket post inserts and vinyl cement work fine, but the panel geometry is non-standard if you try to mix a generic section with an existing PGT run. Bradford Remodeling Co Dallas is an independent service provider and not affiliated with PGT, which means we can install OEM or quality aftermarket parts without pushing one over the other. We recommend OEM when the fence is under 10 years old and you’re matching a long uninterrupted sight line. After 10 years, UV fading makes any patch visible, so we’ll talk through the aftermarket option honestly.
Styles & brands we work with
Signs Your PGT Fence Installation Is Failing
- Post lean at ground line. This is the number one PGT fence failure in Dallas. Clay soil holds water against the post base through wet springs, then bakes hard in summer. The post rusts or rots right at grade, and the panel starts leaning within weeks. We see it most in Lakewood and East Dallas yards with mature trees shading the fence line.
- Sagging gate with a widening gap at the latch. The hinge brackets PGT uses on aluminum gates pull at the post under weight. Once the post flexes past about 5 degrees, the gate will never self-correct. Cranking the hinges just stresses the bracket further.
- Cracked vinyl pickets at the rail joints. Vinyl expands in Dallas heat, and if a section was installed tight to the post in cooler weather, it has nowhere to go in August. Pickets crack at the routed slots where they meet the bottom rail. A few hairline cracks are cosmetic; a picket that snaps free means water is getting into the rail.
- Rattling panels in high wind. Dallas gets real straight-line winds off the plains, and a PGT fence that was installed with undersized or missing rail brackets will rattle like a loose gutter. The panel stays up, but every wind event works the fasteners until they round out the rail holes.
- White chalky residue on aluminum rails. That’s aluminum oxide forming where the factory powder coat has been scratched or worn through by a rubbing gate or a lawn mower. In Dallas humidity, the oxidation spreads under the coating and lifts it in sheets. Once that starts, the rail needs replacement, not touch-up paint.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a full PGT fence installation in Dallas, expect $3,500 to $9,000 installed. That range covers a typical 100 to 200 linear foot residential run. The low end assumes standard 4-foot aluminum or 6-foot vinyl sections with good post spacing and no major grading issues. The high end assumes PGT’s taller 6-foot aluminum, gate replacement, post excavation in rocky or root-heavy soil, and disposal of the old fence line. A single gate replacement, which is the most common partial job we quote, runs $600 to $1,400 installed depending on gate width and whether the post itself needs resetting in concrete.
Every PGT fence installation quote from Bradford Remodeling Co Dallas includes the sections, brackets, fasteners, post concrete, labor, and haul-off. No line item appears at the door that wasn’t on the written price. The work is covered by the 365-Day Done Right Promise: if a post shifts, a gate sags, or a panel bracket fails within a year of install, we come back and correct it at no charge. That’s in writing, and it’s the same standard we’ve held across Dallas since joining the Garrison Partners family in 2004.
DIY or Call Us?
There are things you can check safely: gate hinge tightness, visible bracket wear, picket cracks, and whether the posts feel solid when you push them. What you shouldn’t do is try to reset a PGT post by yourself. Digging out an 18 to 24 inch concrete footing in Dallas clay is a full day of labor with a post hole digger, and you risk busting the bottom rail of a good panel in the process. We’ve also seen homeowners mix quick-setting concrete that doesn’t cure correctly in Dallas heat and have the post lean again in six weeks.
If the gate is off its hinges or the post is leaning past a few degrees, call (903) 326-8963. We’ll come out, confirm what’s failing, and give you a written quote before any work starts. Straight number, real scope, no surprises on delivery day.
FAQs
A properly installed PGT aluminum fence in Dallas lasts 20 to 30 years. PGT vinyl typically runs 15 to 25 years. The failure point is almost never the panel; it’s the post footing. Dallas clay soil shrinks in drought and expands in wet seasons, and that movement is what eventually works a post loose. Correct installation with 18 to 24 inches of concrete below the frost and drainage line is the difference between a fence that lasts decades and one that leans in five years. Call (903) 326-8963 for an exact assessment of your fence line, the estimate is free.
Yes, in most cases. A single leaning post can be extracted and re-set, a sagging gate can be re-hung with fresh brackets, and cracked pickets can be swapped without replacing an entire section. The repair-only path usually runs 20% to 40% of the cost of a full panel replacement. Where repair stops making sense is when three or more posts along the same run are failing, or when the rail fasteners have rounded out the aluminum. At that point you’re chasing a problem that comes back. Call (903) 326-8963 and we’ll give you a written price for both paths and let you choose.
Most PGT fence installations in Dallas are one to two days for a typical residential run. A single post reset or gate re-hang is usually half a day. The variables are concrete cure time, which runs 24 to 48 hours before we hang a full gate on a fresh post, and line locates if you’re in a Dallas neighborhood with shallow utilities like Las Colinas or parts of Richardson. We schedule all of that before the first tool comes off the truck.
We stock the most common PGT-compatible bracket kits, gate hinges, post caps, and vinyl picket packs on our Dallas service vehicles. Full PGT aluminum sections are typically pulled from our local supplier the same week, not the same day. If you’re mid-demo and waiting on a section, we’ll leave the fence line stable and secure until the ordered part arrives. We also stock parts for KraftMaid, Cambria, and Silestone on the cabinet and countertop side, but on fence work PGT is what we carry.
Written by Curtis Lane, Owner, Bradford Remodeling Co Dallas at Bradford Remodeling Co Dallas, serving Dallas and nearby areas.
