Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CWS Kitchen Remodeling: The Dallas Owner’s Guide
A full CWS kitchen remodel in Dallas runs $14,000 to $45,000 installed, depending on cabinet line, countertop material, and whether any walls or plumbing move. Bradford Remodeling Co Dallas stocks and installs CWS-compatible cabinetry, hardware, and structural components, and we match existing CWS door profiles and finish codes so you’re not stuck buying a whole new kitchen over one failed run of cabinets or a delaminated door face.
Most Dallas homeowners call us after they open a lower cabinet and find swollen MDF edges, or a hinge plate has pulled loose from a stile for the second time in five years. Texas humidity does not forgive particleboard. We see it in Preston Hollow, Lake Highlands, the M Streets, and every 1980s starter home in Richardson, Garland, and Mesquite. The kitchen still works. The CWS parts inside it are reaching the end of their service life. That is exactly what this page is for.
Key Takeaways:
- CWS kitchen remodel parts installed in Dallas: $14,000 – $45,000 full scope, with cabinet-only work from $4,000
- We match CWS door series, finish codes, and hinge layouts so you repair what failed, not tear out what is still sound
- Every CWS-compatible part we install is covered by the 365-Day Done Right Promise: if it fails within one year, we return and correct it at no charge
- Bradford Remodeling Co Dallas is an independent contractor, not affiliated with CWS. We work on CWS products because they are all over Dallas, not because CWS signs our checks.
Which CWS Models This Applies To
CWS, or Custom Wood Products, built kitchens through dealerships and regional builders for decades. In Dallas, you’ll find CWS cabinetry in late-1990s and early-2000s homes from builders like David Weekley, Darling, and a handful of custom shops that worked the Park Cities and Preston Hollow. The cabinet boxes were typically 1/2-inch and 3/4-inch plywood or MDF with hardwood face frames, finished in sprayed conversion varnish.
Here is the compatibility gotcha most Dallas homeowners run into: CWS made several door profile families, and the shops that installed them did not label the boxes. The series name is not stamped inside the drawer box like KraftMaid does. You identify a CWS door by its outside profile cut and the finish code tag on the back of the drawer face. If that tag is gone, we measure the rail and stile width, the reveal between the panel and the frame, and match it to the nearest current-equivalent profile from our vendor network. We stock the most common CWS shaker and raised-panel profiles in maple and cherry. Rarer thermofoil laminates are ordered to spec, usually a two-week lead.
For CWS specifically, we recommend OEM-match door and drawer fronts over aftermarket knock-offs when the finish is stained, because the stain blend is the hardest thing to get right. For painted white and off-white doors, a quality aftermarket match from a shop that uses the same conversion varnish system is often indistinguishable and costs 20 to 30 percent less. We will lay both options out in writing before you spend a dollar.
Styles & brands we work with
Signs Your CWS Kitchen Remodeling Is Failing
Dallas kitchens with CWS components fail in predictable ways. This is what we see, in order of how often:
- Swollen or darkened bottom edges on sink-base doors. The conversion varnish was never meant to stand in water. Ten to fifteen years of Dallas humidity and the occasional sink overflow wicks into the MDF core. The door is done, but the box may be fine. That is a door-front replacement, not a cabinet teardown.
- Hinge plates pulling out of the stile. CWS used a 35mm cup hinge with a plastic dowel-and-screw mounting plate on many lines. The plastic fatigues, the screw backs out, and the door sags. We re-drill, insert hardwood blocking behind the plate, and re-mount with longer screws into solid wood. The door almost never needs full replacement for this.
- Drawer glides that feel like a shopping cart wheel. Older CWS rollouts used a side-mount epoxy-coated glide with a nylon wheel. Once the wheel flattens, the drawer grinds. This is a $40-per-drawer part and a one-hour fix, but you need to catch it before the drawer box wears a groove into itself.
- Faded or cloudy finish on doors facing west windows. Dallas UV is relentless. Conversion varnish fades unevenly, and a door that used to match its neighbors no longer does. We can refinish on site if the core is sound, or replace the affected fronts if the core has blown.
- Cabinet boxes that have begun to rack or separate at the corners. This is structural, usually from an undermount sink leaking for years or a slab floor that has shifted. The box is compromised. We evaluate whether a box can be sistered and re-squared, or whether that cabinet run becomes part of a larger remodel.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full CWS-compatible kitchen remodel in Dallas runs $14,000 to $45,000 with Bradford Remodeling Co Dallas. That range covers the entire scope: demo, cabinet installation, countertop fabrication and install, backsplash, plumbing and electrical rough-in work if needed, and finish trim. Where you land in that range depends on cabinet count and material, square footage of countertop, and whether we are moving a sink or a range line. A smaller kitchen with stock-size cabinets and laminate tops starts around $9,000. Cabinet-only replacement of a run of CWS boxes runs $4,000 to $13,000. Countertop-only work is $2,000 to $6,500 installed. Backsplash sits at $800 to $2,500.
Every line-item price is written before work begins, and it does not move at the door. That is The Garrison Standard, and it applies to a $900 replacement door front exactly the same as a $45,000 kitchen. The written scope names the specific CWS-compatible parts, the cabinet series we are matching, the exact countertop slab, the hardware finish, and the labor. You get a signed copy. We do not change the number mid-job unless you change the scope, and if you do, we price that change in writing before we pick up a tool.
All completed CWS repair and remodel work carries the 365-Day Done Right Promise. If our install fails inside one full year, Bradford Remodeling Co Dallas returns and corrects it at no charge. That includes doors coming out of square, hinge plates pulling loose, drawer glides failing, and delaminating seams. A straight number, a real scope, and warranty terms in your hand before any work starts.
DIY or Call Us?
You can check a few things safely. Look at the drawer glide rail and see if the nylon wheel is flat or the rail is bent. Look at the hinge plate screws and see if they spin in their holes. Remove the drawer and check the bottom panel for swelling. Those are inspection points, not repairs.
What you should not do yourself is attempt to re-drill stripped hinge plates with heavier screws, especially if your technique is “put a bigger screw in there” while the door sags off the box. A cabinet door is not under spring tension, but a 20-pound door falling off a failed mounting plate will crack a granite countertop or a tile floor faster than you can catch it. A cracked slab is a $1,200 problem on top of the $40 hinge fix. It is the classic dollar-waiting-on-a-dime repair.
We stock the common CWS matching profiles, hinge plates, screws, glides, and bumpers on the truck, so most single-cabinet calls in Dallas are one visit. Call (903) 326-8963 and we will tell you what we think over the phone. If it sounds like a door front and two glides, we will give you a real number before we show up.
FAQs
Twenty to thirty years if the kitchen was dry and the doors were not abused, but the hardware usually fails twice as fast as the boxes. Expect hinge plates and drawer glides to need attention at the 10-to-15 year mark in Dallas, where summer humidity puts constant moisture load on every MDF seam. Swollen edges on doors facing a dishwasher or sink are the first to go.
Yes, if the finish is the issue and the substrate is sound. We strip and re-spray conversion varnish on site for faded or cloudy doors that have not delaminated. If the MDF or the plywood core has blown, the door is done and there is no honest repair. We will tell you which one you have before you spend anything.
A single door front with stock hinges and a glide swap is a half-day visit and often done in one trip. A run of eight to ten cabinet boxes with new fronts, hardware, and finish matching takes two to three days, including dry time between coats. A full kitchen is four to eight weeks depending on countertop templating and cabinetry lead times. We put the completion window in writing with the price, and we hold to it.
We keep the common CWS-compatible shaker and raised-panel door profiles in maple and cherry, plus hinge plates, screws, glides, and bumpers, on the truck for same-visit replacement. Specialty CWS laminate profiles and less common hardwoods are ordered to spec with a two-week lead. We also stock complementary parts for KraftMaid, Cambria, and Silestone kitchen systems, so mixed-spec Dallas kitchens can be handled in one scope.
Written by Curtis Lane, Owner, Bradford Remodeling Co Dallas at Bradford Remodeling Co Dallas, serving Dallas and nearby areas.
