Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Fence Installation: The Dallas Owner’s Guide
Barrette fence installation in Dallas typically runs $3,500 to $9,000 for a complete perimeter job, depending on linear footage, terrain, and whether we’re pulling old posts or setting new ones. We stock Barrette-compatible rails, pickets, post caps, and gate hardware on the truck for most common panel profiles, which means the swap usually happens the same week we give you the written price. Most Dallas homeowners discover they need this work after a Texas thunderstorm folds a section like cheap lawn furniture, or when a post finally rots at the soil line and the whole run starts listing toward the neighbor’s yard.
You’re here because you have Barrette product and something’s not holding. Maybe the bottom rail cracked at the bracket, maybe a gate sags so hard it drags a groove in the St. Augustine, maybe the pickets are cupping and pulling screws out of the rails. Whatever failed, you want it matched, priced, and fixed without a three-week song and dance. That’s the page we’re writing here.
Key Takeaways
- Installed Barrette fence pricing in Dallas: $3,500 – $9,000 for a full run; smaller section repairs and gate rebuilds land lower.
- We match Barrette’s common panel and post profiles; if yours is a discontinued series, we’ll tell you on the first visit and price the closest compatible system in writing.
- Texas heat and clay soil are the two things that kill Barrette vinyl and aluminum fences here. We’ll explain what that means for your specific failure below.
- Every job gets a written price before work starts and the 365-Day Done Right Promise after it’s finished.
Which Barrette Models This Applies To
Barrette Outdoor Living builds fence under a handful of product lines, and the parts do not all interchange. The big ones we see in Dallas yards are the vinyl privacy panels sold through big-box home centers, the aluminum ornamental lines, and the composite-look semi-private panels. If your pickets are vinyl with a tongue-and-groove fit and your rails are reinforced with aluminum inserts, you’re almost certainly working with Barrette’s vinyl privacy series. If the sections are welded aluminum with spear-topped pickets and a powder-coat finish, that’s the ornamental side of the line.
Here’s the compatibility gotcha Dallas owners run into: Barrette changed rail profile dimensions on several vinyl lines around 2018. The older 2-inch rails don’t seat into the newer 1.75-inch post routs, and you won’t see the difference until the old rail is already out of the ground. If your fence went in before 2018 and you’re ordering replacement sections yourself, measure the rail width and the post rout opening before you buy anything. We check this on the first visit so the parts we bring actually fit your standing posts.
On OEM versus aftermarket: Barrette’s original parts are fine, but for vinyl we typically recommend OEM-matched rail and picket profiles because the color and grain pattern drift noticeably with third-party stock. Blazing hot Dallas sun fades vinyl unevenly anyway, and a mismatched replacement section will announce itself within two summers. For aluminum, quality aftermarket brackets and post caps are usually indistinguishable from Barrette’s own, as long as you match the post size and the finish. Curtis Lane, who runs Bradford Remodeling Co Dallas, would rather tell you the truth about that than sell you a brand tax.
Bradford Remodeling Co Dallas is an independent contractor. We are not affiliated with Barrette Outdoor Living, which means our written price and our one-year guarantee come from us, not from a manufacturer’s warranty department.
Styles & brands we work with
Signs Your Barrette Fence Installation Is Failing
- Posts leaning at the soil line. This is almost always rot at the base of a wood post inside a vinyl sleeve, or a shallow concrete footing that Texas clay has heaved and cracked. The panel didn’t fail; the foundation under it did.
- Rails sagging between posts. Vinyl rails creep in Dallas heat, especially on south-facing runs that bake all afternoon. A rail that should span eight feet starts bowing at seven and a half, and the pickets follow.
- Gate dragging or not latching. Gate posts take more load than any other post in the run. When the post flexes or the hinges wear, the latch stops lining up. You can shim it for a while, but the real fix is re-setting the post and rebuilding the gate frame square.
- Pickets cupping, cracking, or popping out of the bottom rail. Vinyl expands and contracts dramatically with Dallas temperature swings from January to August. Once a picket splits at a screw point, water gets in and the split widens every freeze-thaw cycle.
- White chalky residue on aluminum panels. That’s the powder coat oxidizing. It’s not structural, but it means the finish has failed and corrosion is next, especially anywhere salt or pool chemicals splash against the metal.
If you’re seeing any of these, the cheapest fix is usually the one you do before the section falls over and takes the neighbor’s sprinkler head with it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a full Barrette fence installation in Dallas, our written price typically lands between $3,500 and $9,000. The spread comes down to three things: how many linear feet you’re running, whether we’re setting new posts or reusing sound ones, and what the ground gives us when we dig. North Texas clay is unforgiving, and sections of Dallas with heavy limestone just below the surface add post-hole labor that a flat-lot quote won’t reflect.
Here’s the line-item breakdown we give every homeowner before work starts:
- Post removal and reset: $45 – $85 per post, concrete and haul-off included when the old post is rotten or leaning.
- New vinyl panel sections (6′ x 8′, Barrette-compatible): $120 – $210 per section, materials only.
- New aluminum panel sections: $140 – $240 per section, depending on ornamental height and finish.
- Gate rebuild (single, including frame, hinges, latch): $350 – $750 installed.
- Full perimeter install, 150 – 250 linear feet: $3,500 – $9,000, all materials, labor, post setting, and clean-up included.
Every price is in writing before the first tool comes out. No change orders because we hit rock. No number that moves at the door. When the job’s done, you get a signed 365-Day Done Right Promise: if the fence fails within a year of install, we come back and make it right at no charge. That’s the Garrison Standard, and it applies to every Barrette installation we do.
DIY or Call Us?
Some Barrette fence work is genuinely homeowner-friendly. Straightening a single picket, tightening a latch, hosing down oxidized aluminum with a soft brush. That’s maintenance, not repair. But before you reach for a post-hole digger, know where this goes wrong in Dallas. Setting a fence post correctly means getting below the clay heave line, which in our soil means a 24-inch minimum depth, usually 30. A post set at 18 inches will lean within two summers. And removing a rotted post without disturbing the two healthy panels attached to it is a two-person job that turns into a three-person job when the concrete doesn’t cooperate.
Also, aluminum fence rails under tension can shift when you unbolt a section. If a gate is involved, you’re dealing with a loaded frame that can pinch fingers fast. We don’t recommend any DIY gate live-load work.
If you want to check the failure yourself before calling, look at the post base first. Dig down six inches with a hand trowel and check for rot or cracked concrete. That tells you whether you need a section replacement or a post reset. Then call (903) 326-8963 and tell us what you found. Straight number, real scope, no surprises on delivery day.
FAQs
A properly set Barrette vinyl or aluminum fence in Dallas should last 20 to 30 years for the panels, with gate hardware and post footings needing attention around the 10- to 12-year mark. Vinyl fades and gets brittle faster on west-facing runs; aluminum holds its shape longer but the powder coat will oxidize in 15 to 20 years. Call (903) 326-8963 if you want us to walk your fence line and tell you how much life is left in it, free.
Yes, if the posts are sound and the damage is confined to rails, pickets, or hardware, we can rebuild the section in place for a fraction of a full replacement. Once a post rots or the concrete footing cracks, the repair has to go to the ground, and that’s a different job. We’ll tell you which one you have before we quote anything.
Most single-run installs and section replacements in Dallas take one to two working days, including post setting and concrete cure time before panels go up. A full perimeter with multiple gates and rocky digging can run three to four days. The written price you get before we start includes the schedule, so there’s no guessing.
We stock common Barrette-compatible vinyl rails, pickets, post caps, and gate hardware on the truck for most standard profiles. If yours is a discontinued series or a specialty color, we’ll handle the order and tell you the lead time before you commit. We also stock brands like KraftMaid, Cambria, and Silestone for interior work, but for fence we carry what Dallas yards actually use.
Written by Curtis Lane, Owner, Bradford Remodeling Co Dallas at Bradford Remodeling Co Dallas, serving Dallas and nearby areas.
