Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Roofing: The Dallas Owner’s Guide
Barrette-compatible roofing repair and replacement in Dallas typically runs $400 to $1,800 installed, depending on whether we’re patching a section or replacing the full run. We stock the common Barrette profiles, flashing, and fasteners on our trucks, so most calls get diagnosed and fixed in a single visit. What usually brings a Dallas homeowner to this page is a leak that started small, maybe a damp spot on the ceiling after a hard spring storm, or granules collecting in the gutter after a hail pass. The part failed quietly, and now you need to know exactly what it costs to make it right.
Bradford Remodeling Co Dallas is an independent service provider. We’re not affiliated with Barrette, but we work with their product lines regularly enough to know how they behave in North Texas weather.
Which Barrette Models This Applies To
Barrette’s roofing line covers a few distinct profiles, and the compatibility gotcha most Dallas homeowners hit is assuming one flashing kit fits all of them. It doesn’t. The ridge caps, drip edges, and closure strips are sized to the specific panel profile, and mixing a standard corrugated closure strip onto a Barrette ribbed panel will leave gaps that wind-driven rain finds in a single Dallas thunderstorm.
To identify what you have, check the underside of any removed panel or the original invoice. Barrette stamps profile codes near the lap edge on most lines, and the panel width is the fastest field check: 36-inch coverage versus 38-inch coverage tells you which generation you’re dealing with. When we spec replacement parts, we match OEM Barrette profiles rather than generic aftermarket equivalents because the lap geometry is the difference between a roof that sheds water and one that wicks it. For fasteners, we use the same neoprene-washered screws specified for the original install, not whatever the big box store has on the shelf.
Styles & brands we work with
Signs Your Barrette Roofing Is Failing
- Leaks at the lap joints, not the middle of the panel. Metal roofing rarely fails in the field of the panel. When water gets through, it’s almost always at a lap, a fastener, or a transition. The lap sealant Barrette uses has a real lifespan, and once it hardens and shrinks, the lap opens up just enough for capillary action to pull water uphill.
- Rust streaking below the fasteners. The neoprene washer is the waterproofing on a screw-down panel roof, not the screw itself. When washers go brittle from UV and Dallas heat, they crack, the screw backs out a few thousandths, and the rust streaks show up on the panel below.
- Granules in the gutter on an asphalt-shingle roof. If your Barrette product is one of their shingle lines, granule loss after a hailstorm is the early warning. Dallas hail doesn’t always tear shingles; it knocks the ceramic granules loose, and the underlying asphalt then bakes and fails within two to three summers.
- Daylight visible at the ridge or eave from inside the attic. This one’s worth checking after any wind event over 40 mph. If the closure strips have shifted or the ridge cap fasteners pulled, you’ll see light where you shouldn’t, and that’s the path every wind-blown rain follows.
- Fastener heads that spin instead of tighten. By the time a fastener does this, the substrate under the panel is saturated or the purlin has rotted. Tightening it does nothing; the panel needs to come up and the decking or purlin needs inspection.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Dallas, Barrette-compatible roof repair runs $400 to $1,800 installed. The low end covers a focused repair: pulling a few panels, replacing failed lap sealant or closure strips, re-fastening with new screws, and re-seating the flashing. The high end covers a larger section replacement where we’re cutting out damaged panels, addressing any rotted substrate beneath, and re-installing to match the existing profile.
What drives the range is access and substrate condition. A single-story roof in Richardson with clean decking is a different job than a two-story in Lakewood where the 1950s-era framing under the metal has been holding moisture. Every quote we write in Dallas includes the parts, the labor, and any substrate repair we can see before we start. We give you the written price before any work begins, and every repair is covered by our 365-Day Done Right Promise: if it fails within the year, we come back and make it right at no charge. That’s The Garrison Standard, and it’s in writing on every job.
DIY or Call Us?
You can safely inspect a Barrette roof from the ground or from a ladder at the eave, looking for the signs above. You should not be on a roof in Dallas in July, and you should not be lifting panels yourself. Metal panel edges are sharp enough to need stitches, and the moment you pull a panel, you’re now responsible for whatever you find underneath. If the decking is rotted, that’s a structural repair, not a roofing patch.
Where DIY goes wrong here is the lap sealant. Homeowners buy a tube of whatever says “roof sealant” at the hardware store, lay a bead over the failed lap, and think they’ve fixed it. They’ve covered it. The water is still getting in at the open lap underneath, and now it’s trapped against the metal. Six months later the decking is worse and the repair bill doubled. If you see signs of failure, call (903) 326-8963 and we’ll put eyes on it. The estimate is free, and you’ll get a straight number before anything gets touched.
FAQs
A properly installed Barrette metal roof in Dallas will last 30 to 50 years, but the lap sealants and fastener washers typically need service at the 12 to 15 year mark, earlier if the roof takes repeated hail. The Dallas climate shortens the sealant lifespan more than the panel lifespan: UV exposure and the freeze-thaw cycle in January and February work the laps harder than a coastal climate ever would. Call (903) 326-8963 and we’ll tell you what condition your laps are actually in.
Yes, in most cases. If the panels themselves are intact and the failure is at laps, fasteners, or flashing, a targeted repair gets you another decade or more of service for $400 to $1,800. Replacement only becomes the right call when panel damage is widespread, usually after a hailstorm that’s left dents and cracked coatings across most of the field. We’ll show you the damage in person and give you both numbers before you decide.
Most Barrette roof repairs in Dallas are completed in a single day. The work itself is usually four to six hours, and the slower part is getting the fasteners and re-sealing done right, not rushing the lap geometry. If substrate repair is needed, the job extends to two days. Weather in Dallas is the real variable, and we don’t open a roof when storms are forecast.
We keep the common profiles, closures, flashing, and fasteners stocked on our trucks, so most jobs don’t wait on a supply order. If you have an older or less common Barrette line, we may need a day or two to source the correct profile rather than improvising with a near-match. Improvising with roofing parts is how leaks happen twice.
If your Barrette roof is showing any of the signs above, call (903) 326-8963 for a free estimate. We’ll give you the written price before any work starts, and the repair is guaranteed in writing for a full year. Straight number, real scope, no surprises on delivery day.
Written by Curtis Lane, Owner, Bradford Remodeling Co Dallas at Bradford Remodeling Co Dallas, serving Dallas and nearby areas.
