Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Belgard Fence Installation: The Dallas Owner’s Guide
A full Belgard fence installation in Dallas typically runs $3,500 to $9,000 for a standard residential perimeter, depending on linear footage, the specific Belgard fence panel series, and what’s underneath the soil. We stock Belgard-compatible posts, panels, and gate hardware on our trucks, and most straight-run replacements go in within one to two working days once the panels are on site. Where Dallas homeowners usually catch the problem first is at the gate: the latch stops throwing, the gate drags on the concrete, or a post has started to lean after a hard freeze-thaw cycle in Blackland Prairie clay.
Belgard fence systems are not sold as kits you can piece together at any lumberyard. They’re engineered modular products with panel dimensions, post spacing, and hardware that have to match the original installation. If your fence was put in before 2018, there’s a good chance the panel profile you have has been updated, and that changes what we order. We’ll confirm the series, measure the actual panel width and post size on site, then give you a written price before any work starts. That’s The Garrison Standard, and it applies to every fence job we take in the Dallas market.
Which Belgard Models This Applies To
Belgard’s fence and gate line spans several collections, and the compatibility rules are tighter than most homeowners expect. The brand’s modular fence panels come in widths of 72 inches and 96 inches, with post sizes of 4×4, 5×5, and 6×6 depending on the series and wind-load requirements for North Texas. If your existing posts are 4×4 and the panel is 72 inches wide, that narrows the field quickly, but the panel’s top rail profile and the gate hinge pocket are what actually determine the correct replacement.
The key distinction is between Belgard’s original fence panel system and the newer Elements line, which changed the post-to-panel connection method. Panels from the older system slide into routed post channels; Elements panels use a face-mount bracket with a different reveal. A panel that looks close but was designed for the other system will not seat correctly, and forcing it creates a gate that sags within a season. When you call us, we’ll ask you to check the inside of one post for a stamped model number, or measure the panel width center-to-center. That step alone saves a second trip and keeps the price where we wrote it.
On OEM versus aftermarket: for Belgard fence installation, we use genuine Belgard panels and posts. The aftermarket equivalents we occasionally see in Dallas don’t carry the same color stability, and the powder coat on the gate hardware fails faster under Texas sun. We also stock hardware from KraftMaid, Cambria, and Silestone for our cabinet and countertop work, but for fences, we don’t substitute. The manufacturer’s dimensional spec is the only spec we trust on a fence that has to hold its line through a Dallas windstorm.
Styles & brands we work with
Signs Your Belgard Fence Installation Is Failing
- Gate drags or won’t latch. The most common cause we see in Dallas is post movement. Clay soil swells and contracts with moisture, and a post set too shallow works loose in a season. The hinge side post rotates just enough to drop the gate, and the latch stops aligning.
- Panel bows between posts. This means the panel’s internal rail has lost its connection to the post, usually from wind fatigue. Dallas sees sustained 20 mph winds regularly, and a loose face-mount bracket flexes until the rail separates.
- Post leans at the base. Water pools at the post base after heavy rain, and the concrete footer wasn’t poured with a crown. In Dallas’ clay-heavy soil, water sits against the post and rots the footing over time.
- Powder coat blistering or peeling. UV exposure in Dallas is hard on Belgard’s darker finishes. Once the coating breaches, the steel underneath starts rusting, and the cosmetic problem becomes structural within a couple of years.
- Rattling panels or loose screws. The hardware holding the panel to the post should not loosen. If it does, the original installation likely skipped thread-locking compound or over-torqued the fasteners and stripped the hole.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a full Belgard fence installation in Dallas, the price range we write is $3,500 to $9,000. A smaller job, like one 72-inch panel and a gate post reset, lands at the lower end. A full perimeter with 96-inch panels, multiple gates, and several posts needing new footers sits at the top. The biggest drivers are linear footage, post size, gate count, and whether we’re pulling and resetting posts or only replacing panels.
Every quote from Bradford Remodeling Co Dallas includes the Belgard materials at our documented cost, labor for removal of the failed sections, new footers where posts move, panel and hardware installation, and haul-away of the old material. You get the full price in writing before we start, and it doesn’t move at the door unless you change the scope. After the job, the 365-Day Done Right Promise covers the work for a full year. If a post shifts or a gate sags inside that window, we return and correct it at no charge. That’s in writing, every time.
DIY or Call Us?
A homeowner can safely check a few things before calling: look for a stamped model number inside the post, measure the panel width, and note whether the gate drags on the hinge side or latch side. That’s useful information, and it helps us quote faster. What we don’t recommend is pulling panels or dig out posts on your own. A Belgard post carries substantial weight, and a panel under tension can swing when the last fastener comes out. We’ve seen homeowners in Dallas get hurt trying to save a panel that wasn’t worth saving.
The part of this job that makes it worth a trained crew is the footer. Clay soil, sloped yards, and North Texas drainage all affect how deep and how wide the post hole needs to be, and getting that wrong means the new post leans before the next rain. We’ll set the posts, match the panels to the original series, and hand you a written guarantee when we’re done. Call (903) 326-8963 for a free estimate, and we’ll come measure.
FAQs
A properly installed Belgard fence should hold its line for 20-plus years in Dallas, with the finish showing UV fade after 8 to 10 years. Poor drainage at the post base is what shortens that lifespan most, not the panel material itself. If you’re seeing movement in year five or six, call (903) 326-8963 and we’ll tell you if it’s a footing issue or a panel defect.
Yes, if the damage is limited to the finish or a single loose bracket, we can repair it; a bent internal rail or separated post channel means replacement. The deciding question is whether the panel still seats firmly in both posts. If it doesn’t, patching it buys you maybe a season. Estimates are free, and we’ll give you a straight answer either way.
Most Belgard fence replacements in Dallas take one to two working days once the panels are on site. Posts that need new footers add a day for concrete cure time before we hang panels. We’ll tell you the exact schedule when we give you the written price.
We order the Belgard panels and hardware for you, matched to your existing series and dimensions. Homeowners who order their own parts run into compatibility problems regularly, especially between the original system and the Elements line. We handle the ordering so the panels that arrive are the panels that fit, and the price includes everything. Call (903) 326-8963 and we’ll verify what you have.
Written by Curtis Lane, Owner, Bradford Remodeling Co Dallas at Bradford Remodeling Co Dallas, serving Dallas and nearby areas.
