Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Fence Installation: The Dallas Owner’s Guide
Boral fence installation in Dallas typically runs $3,500 to $9,000 for a full replacement, depending on linear feet, existing post conditions, and whether the old gate hardware carries over. We stock Boral-compatible components and can usually complete the teardown, post set, panel install, and gate re-hang inside two to three working days once materials are confirmed. Most Dallas homeowners discover the problem the hard way: a panel starts sagging after a heavy rain, the bottom rail shows rot or splitting at the post connection, or the gate starts dragging because the post has shifted in expansive clay soil.
If you’re reading this, you probably already own Boral fence product and something has failed or is failing. You want the right replacement part matched to your existing line, a straight price, and a crew that won’t leave the old panels piled in your yard. That’s exactly what this page covers.
Which Boral Models This Applies To
Boral fencing is sold under a few distinct product lines, and not every rail, picket, or post cap crosses between them. The two you’re most likely dealing with in Dallas are the Boral Select line (smooth, uniform pickets with a consistent profile) and the Boral Timberline line (wood-grain textured surface meant to read as cedar without the maintenance). Pickets from one line will not match the other visually, even if the dimensions are identical. If you’re replacing a single panel or a run of pickets, match the line first, then the profile.
To identify what you have, look at the back side of a picket or the bottom edge of a rail. Boral embeds a small mold code, usually a letter-number sequence, near one end. Write that down before you call anyone. Rail dimensions matter too: Boral rails commonly come in 1.5-inch by 5.5-inch and 1.5-inch by 7.25-inch profiles, and mixing them on the same frame will cause alignment problems at the post brackets. Gate hardware on Boral systems uses a specific bracket spacing; universal aftermarket brackets often sit proud of the rail face and leave the gate with visible gaps at the hinge side. We’ve corrected enough of those in the Lakewood and East Dallas neighborhoods to know the difference a bracket’s standoff height makes.
One more compatibility gotcha for Dallas specifically: Boral products are designed for standard 8-foot post spacing, but some early installations in this market used 96-inch panels on 94-inch centers to save material. If your posts were set off-standard, a stock Boral panel will not drop in without modification. We measure center-to-center on every post before ordering anything.
Bradford Remodeling Co Dallas is an independent service provider. We are not affiliated with Boral. We install and repair Boral-compatible fence systems using OEM parts where available and quality aftermarket equivalents where they make practical and financial sense.
Styles & brands we work with
Signs Your Boral Fence Installation Is Failing
- Panel sag at the mid-span. Boral rails are engineered for specific spans, and when posts shift in Dallas clay or the bottom rail wicks moisture from ground contact, the panel starts to bow between posts. The cause is almost always a failing post connection, not a bad panel.
- Gate dragging on one corner. When a gate post leans outward even half an inch, the latch side drops and the gate scrapes the ground or the latch plate. In Dallas, post lean is usually caused by insufficient footing depth in expansive soil, not by the gate hardware itself.
- Bottom rail splitting at the bracket screws. Boral’s cellular PVC material holds screws well until the rail is stressed laterally. If the bottom rail shows hairline cracks radiating from the bracket mounts, the rail is done. Tightening the screws only widens the split.
- White chalky residue on pickets. This is surface oxidation, not structural failure, but it signals the UV-protective coating has worn through. Once the base material is exposed to Dallas sun for a full season, the picket becomes brittle and will snap at the top or bottom on impact.
- Pickets pulling free from the top rail. This happens when the top rail expands at a different rate than the pickets during temperature swings. Dallas sees 40-degree shifts in a single week during spring and fall, and over time that cycle works staples or trim screws loose.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a full Boral fence installation in Dallas, expect $3,500 to $9,000 installed. The spread comes down to three things: total linear footage, how many posts need to be reset or replaced, and whether we’re matching an existing Boral line with OEM material or aftermarket equivalent. A 100-foot run with healthy posts and simple gate re-hang lands near the lower end. A 200-foot run with every third post leaning, two gates, and Timberline grain-matched pickets lands near the top.
Every quote we write for fence work in Dallas includes the teardown and haul-off of old material, new posts set to code depth with proper concrete, rail and picket installation, gate hardware replacement, and the signed 365-Day Done Right Promise at close. The written price you get before work starts is the price you pay. No numbers move at the door. If a post shifts or a bracket fails inside that year, we come back and correct it at no charge.
Here’s the line-item breakdown we show on every Dallas fence quote:
- Teardown and disposal: $400 – $900 depending on length and dump fees
- Post removal and reset (per post): $85 – $160 when replacement is needed
- Boral-compatible panel and rail install (per 8-foot section): $65 – $110 including labor
- Gate re-hang or replacement: $250 – $600 per gate including hardware
- Grain-matched Timberline picket upgrade: adds 15 – 25% to material line
DIY or Call Us?
Fence work is not inherently dangerous the way a garage spring or a live panel is, but it can go sideways fast in Dallas soil. You can safely pull a loose picket, check the mold code on the back, and measure your post spacing. That information is useful whether you call us or someone else.
Where DIY goes wrong is at the post. Digging a 30-inch footing in Texas black clay by hand is a full day of work, and if you set a post even two degrees off plumb, the entire panel run will show it by the time the concrete cures. Gate posts are worse: a gate that weighs 50 pounds acts on the post like a lever every time it swings. Get the footing depth or the concrete mix wrong, and the post is leaning again before the season changes. If your failure is panel-level, a skilled homeowner can handle it. If it’s post-level, call us at (903) 326-8963 and we’ll put a square on the whole run while we’re out there.
FAQs
A properly installed Boral fence in Dallas lasts 20 to 25 years before the material shows meaningful fatigue, provided the posts were set below the clay line and the bottom rail was kept off direct grade. The material itself doesn’t rot, but UV exposure and thermal cycling in this market will eventually make pickets brittle. Call (903) 326-8963 and we’ll tell you honestly whether your fence is at end-of-life or worth a partial repair.
Yes, in most cases. A cracked bottom rail, loose pickets, or a shifted post can be corrected without replacing the full run. The exception is when the pickets themselves have gone brittle from sun exposure; patching one brittle picket usually leads to the neighbor picket snapping next week. We’ll tell you which situation you have before you spend a dollar.
Most full installations in Dallas run two to three working days from teardown to final gate adjustment. If we’re resetting posts, we usually let the concrete cure a full 24 hours before hanging panels. You’ll have a written schedule before we start, and the crew won’t disappear mid-job.
We stock common Boral-compatible rail profiles, pickets, post caps, and gate brackets on our trucks, along with aftermarket equivalents that match the most common Dallas installations. For Timberline grain-matched material or unusual panel lengths, we order ahead and schedule your install once the materials land. We also stock parts for KraftMaid, Cambria, and Silestone projects, but fence work runs on its own material logs.
Written by Curtis Lane, Owner, Bradford Remodeling Co Dallas at Bradford Remodeling Co Dallas, serving Dallas and nearby areas.
