Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Therma-Tru Roofing: The Dallas Owner’s Guide
We stock and install Therma-Tru-compatible roofing components across Dallas, with most replacements running $845 to $2,400 installed depending on the part and your roofline. Most owners find the failure the same way: a leak shows up on the ceiling after a spring storm, or a visual inspection turns up cracked flashing, failed sealant beads, or a warped curb mount around a skylight or vent. The fix is usually a same-scope replacement of the failed component, not the whole roof, and Bradford Remodeling Co Dallas puts that price in writing before we touch the ladder.
One note before we go further: Bradford Remodeling Co Dallas is an independent service provider. We’re not affiliated with Therma-Tru, but we’ve installed and serviced their roofing-adjacent products long enough to know the compatibility quirks that send homeowners in circles. Curtis Lane has been running crews in this market for the better part of two decades, and a roof leak in Dallas doesn’t give you two decades to sort it out.
Which Therma-Tru Models This Applies To
Therma-Tru’s roofing-adjacent product line is smaller than their door catalog, but the parts that tie into a roof matter more per square inch than most homeowners realize. We’re talking about the flashing kits, curb mounts, gasket sets, and vent collars used with Therma-Tru skylights, roof-mounted vent blocks, and their exterior trim profiles that terminate at the eave line. The compatibility gotcha that trips up Dallas homeowners: Therma-Tru flashing kits are keyed to specific skylight frame dimensions, not universal. A flashing kit for a 24-inch curb frame will not seat correctly on a 22.5-inch frame, and the gap won’t show itself until the first hard rain. Where to find your model data: the product label is usually etched or stamped into the frame rail or the curb’s interior lip, visible once the screen or shade assembly is removed. Take a photo of that label before you call anyone. It saves a second trip and a wrong part.
On the OEM-versus-aftermarket question: for door thresholds and brickmould, quality aftermarket parts often match or exceed OEM at 30 to 40 percent less. For roof-integrated flashing and curb mounts, we lean OEM or direct-spec aftermarket. The gauge of the lead or aluminum, the depth of the step profile, and the sealant channel geometry all have to match what the original frame was built for. Dallas sun does not forgive a sealant channel that’s a quarter-inch shallow.
Styles & brands we work with
Signs Your Therma-Tru Roofing Is Failing
- Water staining on the ceiling beneath a skylight or vent. The first culprit is almost always the flashing or the gasket, not the glass or the shingles. Water follows the path of least resistance, and a failed curb-mount gasket directs it straight down the chase.
- Dried, cracked, or peeling sealant beads around the curb or vent collar. UV exposure in Dallas breaks down even premium sealants in five to eight years. The bead will show hairline cracks long before it lets water through, so this is one to catch early.
- Visible rust or corrosion on flashing edges. Sweating and condensation under Texas temperature swings will rust light-gauge flashing from the inside out. By the time the rust shows on the leading edge, the buried section is worse.
- Daylight visible through the frame joint when viewed from the attic. If you can see light, water has already found the same gap. This is the point where you want a documented fix, not a caulk-and-hope.
- Curled or lifting shingles around the curb or vent base. Water has already been pooling there. Shingles curl first, then the substrate softens, then the decking goes. The repair cost climbs with each of those steps.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in Dallas lands in the $845 to $2,400 range for most Therma-Tru roofing-component replacements. Here’s the line-item breakdown we give every homeowner before work starts:
- Flashing or curb-mount replacement: $845 – $1,650 depending on frame size and roofline pitch
- Gasket and sealant set replacement: $380 – $700 when done as a standalone call
- Full curb rebuild (when the substrate has softened): $1,600 – $2,400 including new blocking and decking patch
- Vent collar or roof boot replacement: $250 – $550
Every price is written down before the first tool leaves the truck. That’s The Garrison Standard we operate under: a written price, no numbers that move at the door, and a 365-Day Done Right Promise on the completed work. If the repair fails inside that year, we come back and correct it at no charge. That’s the guarantee, in writing, in your hand before we walk off the job.
DIY or Call Us?
Here’s the honest split. You can safely do the visual checks we listed above from the ground or from inside the attic. A homeowner with a ladder should not be on a steep Dallas roofline handling flashing around a curb mount. Falls from roof height are the leading cause of construction fatalities in this country, and a two-story pitch with morning dew on it is not the place to learn. The other honest reality: a failed curb gasket or flashing isn’t a caulk fix. If you’ve got water traveling through the chase, you need the flashing lifted, the old sealant cut out, the substrate checked, and the new part set in sequence. That’s a trained crew with fall protection, not a Saturday project.
The call is (903) 326-8963. We answer with a live person, 24/7. Straight number, real scope, no surprises on delivery day.
FAQs
In our Dallas climate, you can expect eight to twelve years from flashing and gasket sets before UV and temperature swings start to break the sealant down. Gulf moisture and the freeze-thaw cycles in February take years off light-gauge products. If yours is past the 10-year mark and you can see cracking at the bead, it’s time to have it looked at. Call (903) 326-8963 and we’ll tell you over the phone whether it’s worth a service call.
Surface-level sealant failure can sometimes be spot-repaired if the substrate hasn’t softened and the flashing is still structurally sound. If the flashing is rusted through or the curb wood has gone soft, a partial repair will buy you months, not years. We won’t charge you to replace something that can be saved. The written estimate tells you which path is actually in front of you. Estimates are free.
A standard flashing or gasket replacement runs three to five hours on site, assuming the decking is sound and we’re not rebuilding the curb. If the curb needs new blocking, plan on a full day. We’ll give you the schedule in the written estimate, and we hit the schedule.
We stock common curb-mount gasket sets, vent collars, and flashing profiles for standard Therma-Tru frame dimensions on our Dallas trucks. Oddball sizes or specialty trim get sourced direct-spec and we bring them to the job. We also maintain parts relationships for the other brands we install, including KraftMaid, Cambria, and Silestone. Call (903) 326-8963 and we’ll confirm availability for your model before you’re on the hook for a service call.
Written by Curtis Lane, Owner, Bradford Remodeling Co Dallas at Bradford Remodeling Co Dallas, serving Dallas and nearby areas.
